Faraday's law of induction is a basic law of electromagnetism predicting how a magnetic field will interact with an electric circuit to produce an electromotive force (EMF)—a phenomenon called electromagnetic induction. It is the fundamental operating principle of transformers, inductors, and many types of electrical motors, generators and solenoids.^{[1]}^{[2]}
The Maxwell–Faraday equation is a generalization of Faraday's law, and forms one of Maxwell's equations.
Contents

History 1

Faraday's law 2

Qualitative statement 2.1

Quantitative 2.2

Maxwell–Faraday equation 2.3

Proof of Faraday's law 3

"Counterexamples" to Faraday's law 4

Faraday's law and relativity 5

Two phenomena 5.1

Einstein's view 5.2

See also 6

References 7

Further reading 8

External links 9
History
A diagram of Faraday's iron ring apparatus. Change in the magnetic flux of the left coil induces a current in the right coil.^{[3]}
Electromagnetic induction was discovered independently by Michael Faraday in 1831 and Joseph Henry in 1832.^{[4]} Also, Faraday was the first to publish the results of his experiments.^{[5]}^{[6]} In Faraday's first experimental demonstration of electromagnetic induction (August 29, 1831^{[7]}), he wrapped two wires around opposite sides of an iron ring or "torus" (an arrangement similar to a modern toroidal transformer). Based on his assessment of recently discovered properties of electromagnets, he expected that when current started to flow in one wire, a sort of wave would travel through the ring and cause some electrical effect on the opposite side. He plugged one wire into a galvanometer, and watched it as he connected the other wire to a battery. Indeed, he saw a transient current (which he called a "wave of electricity") when he connected the wire to the battery, and another when he disconnected it.^{[8]} This induction was due to the change in magnetic flux that occurred when the battery was connected and disconnected.^{[3]} Within two months, Faraday had found several other manifestations of electromagnetic induction. For example, he saw transient currents when he quickly slid a bar magnet in and out of a coil of wires, and he generated a steady (DC) current by rotating a copper disk near the bar magnet with a sliding electrical lead ("Faraday's disk").^{[9]}
Michael Faraday explained electromagnetic induction using a concept he called lines of force. However, scientists at the time widely rejected his theoretical ideas, mainly because they were not formulated mathematically.^{[10]} An exception was James Clerk Maxwell, who used Faraday's ideas as the basis of his quantitative electromagnetic theory.^{[10]}^{[11]}^{[12]} In Maxwell's papers, the timevarying aspect of electromagnetic induction is expressed as a differential equation which Oliver Heaviside referred to as Faraday's law even though it is different from the original version of Faraday's law, and does not describe motional EMF. Heaviside's version (see Maxwell–Faraday equation below) is the form recognized today in the group of equations known as Maxwell's equations.
Lenz's law, formulated by Heinrich Lenz in 1834, describes "flux through the circuit", and gives the direction of the induced EMF and current resulting from electromagnetic induction (elaborated upon in the examples below).
Faraday's experiment showing induction between coils of wire: The liquid battery (right) provides a current which flows through the small coil (A), creating a magnetic field. When the coils are stationary, no current is induced. But when the small coil is moved in or out of the large coil (B), the magnetic flux through the large coil changes, inducing a current which is detected by the galvanometer (G).^{[13]}
Faraday's law
Qualitative statement
The most widespread version of Faraday's law states:
This version of Faraday's law strictly holds only when the closed circuit is a loop of infinitely thin wire,^{[16]} and is invalid in other circumstances as discussed below. A different version, the Maxwell–Faraday equation (discussed below), is valid in all circumstances.
Quantitative
The definition of surface integral relies on splitting the surface Σ into small surface elements. Each element is associated with a vector dA of magnitude equal to the area of the element and with direction normal to the element and pointing “outward” (with respect to the orientation of the surface).
Faraday's law of induction makes use of the magnetic flux Φ_{B} through a hypothetical surface Σ whose boundary is a wire loop. Since the wire loop may be moving, we write Σ(t) for the surface. The magnetic flux is defined by a surface integral:


\Phi_B = \iint\limits_{\Sigma(t)} \mathbf{B}(\mathbf{r}, t) \cdot d \mathbf{A}\ ,
where dA is an element of surface area of the moving surface Σ(t), B is the magnetic field (also called "magnetic flux density"), and B·dA is a vector dot product (the infinitesimal amount of magnetic flux). In more visual terms, the magnetic flux through the wire loop is proportional to the number of magnetic flux lines that pass through the loop.
When the flux changes—because B changes, or because the wire loop is moved or deformed, or both—Faraday's law of induction says that the wire loop acquires an EMF, \mathcal{E}, defined as the energy available from a unit charge that has travelled once around the wire loop.^{[16]}^{[17]}^{[18]}^{[19]} Equivalently, it is the voltage that would be measured by cutting the wire to create an open circuit, and attaching a voltmeter to the leads.
Faraday's law states that the EMF is also given by the rate of change of the magnetic flux:

\mathcal{E} =  {\partial t}
(in SI units) where \nabla\times is the curl operator and again E(r, t) is the electric field and B(r, t) is the magnetic field. These fields can generally be functions of position r and time t.
The Maxwell–Faraday equation is one of the four Maxwell's equations, and therefore plays a fundamental role in the theory of classical electromagnetism. It can also be written in an integral form by the KelvinStokes theorem:^{[22]}

\oint_{\partial \Sigma} \mathbf{E} \cdot d\boldsymbol{\ell} =  \int_{\Sigma} \frac{\partial \mathbf{B}}{\partial t} \cdot d\mathbf{A}

where, as indicated in the figure:

Σ is a surface bounded by the closed contour ∂Σ,

E is the electric field, B is the magnetic field.

dℓ is an infinitesimal vector element of the contour ∂Σ,

dA is an infinitesimal vector element of surface Σ. If its direction is orthogonal to that surface patch, the magnitude is the area of an infinitesimal patch of surface.
Both dℓ and dA have a sign ambiguity; to get the correct sign, the righthand rule is used, as explained in the article KelvinStokes theorem. For a planar surface Σ, a positive path element dℓ of curve ∂Σ is defined by the righthand rule as one that points with the fingers of the right hand when the thumb points in the direction of the normal n to the surface Σ.
The integral around ∂Σ is called a path integral or line integral.
Notice that a nonzero path integral for E is different from the behavior of the electric field generated by charges. A chargegenerated Efield can be expressed as the gradient of a scalar field that is a solution to Poisson's equation, and has a zero path integral. See gradient theorem.
The integral equation is true for any path ∂Σ through space, and any surface Σ for which that path is a boundary.
If the path Σ is not changing in time, the equation can be rewritten:

\oint_{\partial \Sigma} \mathbf{E} \cdot d\boldsymbol{\ell} =  \frac{d}{dt} \int_{\Sigma} \mathbf{B} \cdot d\mathbf{A}.
The surface integral at the righthand side is the explicit expression for the magnetic flux Φ_{B} through Σ.
Proof of Faraday's law
The four Maxwell's equations (including the Maxwell–Faraday equation), along with the Lorentz force law, are a sufficient foundation to derive everything in classical electromagnetism.^{[16]}^{[17]} Therefore it is possible to "prove" Faraday's law starting with these equations.^{[23]}^{[24]} Click "show" in the box below for an outline of this proof. (In an alternative approach, not shown here but equally valid, Faraday's law could be taken as the starting point and used to "prove" the Maxwell–Faraday equation and/or other laws.)

"Counterexamples" to Faraday's law

Faraday's disc electric generator. The disc rotates with angular rate ω, sweeping the conducting radius circularly in the static magnetic field B. The magnetic Lorentz force v × B drives the current along the conducting radius to the conducting rim, and from there the circuit completes through the lower brush and the axle supporting the disc. This device generates an EMF and a current, although the shape of the "circuit" is constant and thus the flux through the circuit does not change with time.

A counterexample to Faraday's law when overbroadly interpreted. A wire (solid red lines) connects to two touching metal plates (silver) to form a circuit. The whole system sits in a uniform magnetic field, normal to the page. If the word "circuit" is interpreted as "primary path of current flow" (marked in red), then the magnetic flux through the "circuit" changes dramatically as the plates are rotated, yet the EMF is almost zero, which contradicts Faraday's law. After Feynman Lectures on Physics Vol. II page 173.
Although Faraday's law is always true for loops of thin wire, it can give the wrong result if naively extrapolated to other contexts.^{[16]} One example is the homopolar generator (above left): A spinning circular metal disc in a homogeneous magnetic field generates a DC (constant in time) EMF. In Faraday's law, EMF is the timederivative of flux, so a DC EMF is only possible if the magnetic flux is getting uniformly larger and larger perpetually. But in the generator, the magnetic field is constant and the disc stays in the same position, so no magnetic fluxes are growing larger and larger. So this example cannot be analyzed directly with Faraday's law.
Another example, due to Feynman,^{[16]} has a dramatic change in flux through a circuit, even though the EMF is arbitrarily small. See figure and caption above right.
In both these examples, the changes in the current path are different from the motion of the material making up the circuit. The electrons in a material tend to follow the motion of the atoms that make up the material, due to scattering in the bulk and work function confinement at the edges. Therefore, motional EMF is generated when a material's atoms are moving through a magnetic field, dragging the electrons with them, thus subjecting the electrons to the Lorentz force. In the homopolar generator, the material's atoms are moving, even though the overall geometry of the circuit is staying the same. In the second example, the material's atoms are almost stationary, even though the overall geometry of the circuit is changing dramatically. On the other hand, Faraday's law always holds for thin wires, because there the geometry of the circuit always changes in a direct relationship to the motion of the material's atoms.
Although Faraday's law does not apply to all situations, the Maxwell–Faraday equation and Lorentz force law are always correct and can always be used directly.^{[16]}
Both of the above examples can be correctly worked by choosing the appropriate path of integration for Faraday's law. Outside of context of thin wires, the path must never be chosen to go through the conductor in the shortest direct path. This is explained in detail in "The Electromagnetodynamics of Fluid" by W. F. Hughes and F. J. Young, John Wiley Inc. (1965).
Faraday's law and relativity
Two phenomena
Some physicists have remarked that Faraday's law is a single equation describing two different phenomena: the motional EMF generated by a magnetic force on a moving wire (see Lorentz force), and the transformer EMF generated by an electric force due to a changing magnetic field (due to the Maxwell–Faraday equation).
James Clerk Maxwell drew attention to this fact in his 1861 paper On Physical Lines of Force. In the latter half of Part II of that paper, Maxwell gives a separate physical explanation for each of the two phenomena.
A reference to these two aspects of electromagnetic induction is made in some modern textbooks.^{[26]} As Richard Feynman states:^{[16]}
Einstein's view
Reflection on this apparent dichotomy was one of the principal paths that led Einstein to develop special relativity:
See also
References

^ Sadiku, M. N. O. (2007). Elements of Electromagnetics (fourth ed.). New York (USA)/Oxford (UK): Oxford University Press. p. 386.

^ "Applications of electromagnetic induction".

^ ^{a} ^{b} Giancoli, Douglas C. (1998). Physics: Principles with Applications (Fifth ed.). pp. 623–624.

^ "A Brief History of Electromagnetism".

^ Ulaby, Fawwaz (2007). Fundamentals of applied electromagnetics (5th ed.). Pearson:Prentice Hall. p. 255.

^ "Joseph Henry". Distinguished Members Gallery, National Academy of Sciences. Retrieved 20061130.

^ Faraday, Michael; Day, P. (19990201). The philosopher's tree: a selection of Michael Faraday's writings. CRC Press. p. 71.

^ Michael Faraday, by L. Pearce Williams, p. 1823

^ Michael Faraday, by L. Pearce Williams, p. 191–5

^ ^{a} ^{b} Michael Faraday, by L. Pearce Williams, p. 510

^ Maxwell, James Clerk (1904), A Treatise on Electricity and Magnetism, Vol. II, Third Edition. Oxford University Press, pp. 178–9 and 189.

^ "Archives Biographies: Michael Faraday", The Institution of Engineering and Technology.

^ Magnetism and electricity: A manual for students in advanced classesPoyser, Arthur William (1892), . London and New York; Longmans, Green, & Co., p. 285, fig. 248. Retrieved 20090806.

^ "Faraday's Law, which states that the electromotive force around a closed path is equal to the negative of the time rate of change of magnetic flux enclosed by the path"Jordan, Edward; Balmain, Keith G. (1968). Electromagnetic Waves and Radiating Systems (2nd ed.). PrenticeHall. p. 100.

^ "The magnetic flux is that flux which passes through any and every surface whose perimeter is the closed path"Hayt, William (1989). Engineering Electromagnetics (5th ed.). McGrawHill. p. 312.

^ ^{a} ^{b} ^{c} ^{d} ^{e} ^{f} ^{g} "The flux rule" is the terminology that Feynman uses to refer to the law relating magnetic flux to EMF.Richard Phillips Feynman, Leighton R B & Sands M L (2006). The Feynman Lectures on Physics. San Francisco: Pearson/AddisonWesley. Vol. II, pp. 172.

^ ^{a} ^{b} Griffiths, David J. (1999). Introduction to Electrodynamics (Third ed.). Upper Saddle River NJ: Prentice Hall. pp. 301–303.

^ Tipler and Mosca, Physics for Scientists and Engineers, p795, google books link

^ Note that different textbooks may give different definitions. The set of equations used throughout the text was chosen to be compatible with the special relativity theory.

^ Essential Principles of Physics, P.M. Whelan, M.J. Hodgeson, 2nd Edition, 1978, John Murray, ISBN 0719533821

^ Nave, Carl R. "Faraday's Law". HyperPhysics. Georgia State University. Retrieved 29 August 2011.

^ Roger F Harrington (2003). Introduction to electromagnetic engineering. Mineola, NY: Dover Publications. p. 56.

^ ^{a} ^{b} Davison, M. E. (1973). "A Simple Proof that the Lorentz Force, Law Implied Faraday's Law of Induction, when B is Time Independent". American Journal of Physics 41 (5): 713–711.

^ ^{a} ^{b} Basic Theoretical Physics: A Concise Overview by Krey and Owen, p155, google books link

^ K. Simonyi, Theoretische Elektrotechnik, 5th edition, VEB Deutscher Verlag der Wissenschaften, Berlin 1973, equation 20, page 47

^ Griffiths, David J. (1999). Introduction to Electrodynamics (Third ed.). Upper Saddle River NJ: Prentice Hall. pp. 301–3. Note that the law relating flux to EMF, which this article calls "Faraday's law", is referred to in Griffiths' terminology as the "universal flux rule". Griffiths uses the term "Faraday's law" to refer to what article calls the "Maxwell–Faraday equation". So in fact, in the textbook, Griffiths' statement is about the "universal flux rule".

^ A. Einstein, On the Electrodynamics of Moving Bodies
Further reading

, Chapter III, §530, p. 178.A treatise on electricity and magnetism, Vol. IIMaxwell, James Clerk (1881), Oxford, UK: Clarendon Press. ISBN 0486606376.
External links

A simple interactive Java tutorial on electromagnetic induction National High Magnetic Field Laboratory

 Highly animated lectureInduction: Faraday's law and Lenz's lawR. Vega

Notes from Physics and Astronomy HyperPhysics at Georgia State University

Faraday's Law for EMC Engineers

Introducing Faraday's lawTankersley and Mosca:

Lenz's Law at work.

A free java simulation on motional EMF

Two videos demonstrating Faraday's and Lenz's laws at EduMation
This article was sourced from Creative Commons AttributionShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, EGovernment Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a nonprofit organization.