M1942 Bayonet

M series bayonet
An M1 Bayonet made by the American Fork & Hoe Co.
Type Bayonet
Place of origin United States
Service history
Used by  United States
Wars Philippine–American War
World War I
Banana Wars
World War II
Korean War
Production history
Manufacturer American Fork & Hoe
Oneida, Ltd.
Pal Blade and Tool
Utica Cutlery
Union Fork & Hoe
Wilde Drop Forge & Tool
Produced from 1905 onward
M1905 bayonet
M1942 bayonet
M1 bayonet
Scabbard/sheath M1905 scabbard

The 'M' series of bayonets was initiated in 1905, and continues in use to the present. There have been several modifications to the original design, the greatest being with the introduction of the M1 subseries near the end of WWII.


The M1905 was made for the .30 caliber U.S. Rifle Model 1903.[1] The M1905 bayonet blade is 16 inches (40.6 cm) long, and the handle is 4 inches (10.1 cm) long. The bayonet also fits the .30 caliber U.S. M1 Garand rifle (or simply, M1). In 1942, the same basic bayonet design (equipped with a plastic instead of a wood handle) was again produced and designated the M1942 bayonet.


The M1942 is an exact copy of the M1905 Bayonet, and was manufactured in sufficient numbers to keep up with wartime production of the .30 caliber M1, which it was intended to be used with. Again, the blade is 16 inches long with a 4 inch long handle. Interchangeability allowed the M1942 bayonet to be used on any M1903 rifle, while allowing the mounting of the earlier M1905 bayonet on the M1 Garand rifles.

M1942 production (1942-1943)
Production by manufacturer [2]
American Fork and Hoe 350,000 23%
Oneida, Limited 235,000 16%
Pal Blade and Tool 250,000 17%
Utica Cutlery 225,000 15%
Union Fork and Hoe 385,000 26%
Wilde Drop Forge and Tool 60,000 4%

The M1 and M1905E1

The M1 Bayonet was designed to be used with the .30 caliber M1 Garand. The blade is 10 inches (25.4cm) long, and the handle is 4 inches (10.1cm) long. Before 1943, the M1 Garand and all variants of the M1903 Springfield rifle were using the M1905 and later M1942 bayonets. In 1943, the U.S. Army decided to shorten the bayonet design. Many of the M1905/M1942s as possible were recalled, had their blades cut down to 10 inches, and were reissued.

The shortened M1905 bayonets were re-designated as M1905E1. New-production 10-inch bayonets were designated as M1 bayonets.

The shortened bayonets functioned well in the European theater, where in the rare bayonet-actions of the time they were matched up against the 9¾ inch long blade of the German S84/98 III bayonet fitted on the Karabiner 98k rifle. However, in the Pacific theater, the much longer Japanese Type 30 sword bayonet on the already very long Arisaka rifle caused many American troops to retain the longer, unmodified M1905 bayonet.


The original M1905 scabbard had a wooden body with a rawhide cover and employed a wire belt-hanger which went over and around the supporting belt. The M1910 scabbard was covered in canvas with a leather tip. Wire cartridge-belt hooks replaced the belt-hanger. The M1910 scabbard was the primary scabbard used during the First World War. Earlier M1905 scabbards were modified by replacing the belt-hanger with a belt hook. A green-leather bodied M1917 scabbard (designed for the M1917 Enfield bayonet) was approved as a substitute for the M1905 bayonet scabbard.

A new scabbard, the M3, was developed early in the Second World War to replace these earlier scabbards. The M3 scabbard had a fiberglass body, with a metal throat, and was equipped with hooks which fixed to the cartridge-belt.[3]

See also


External links

  • Olive Drab
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.