World Library  
Flag as Inappropriate
Email this Article

Dynamic Design Analysis Method

 

Dynamic Design Analysis Method

All mission-essential equipment on board Naval ships and submarines must be qualified for shock loads caused by underwater explosions.

The Dynamic Design Analysis Method (DDAM) is a US Navy-developed analytical procedure for evaluating the design of equipment subject to dynamic loading caused by underwater explosions (UNDEX). The analysis uses a form of shock spectrum analysis that estimates the dynamic response of a component to shock loading caused by the sudden movement of a naval vessel. The analytical process simulates the interaction between the shock-loaded component and its fixed structure, and it is a standard naval engineering procedure for shipboard structural dynamics.

Contents

  • Background and rationale 1
  • Analysis methodolgy 2
  • Reporting formats 3
  • References 4

Background and rationale

All mission-essential equipment on board military surface ships and submarines must be qualified for underwater shock loads caused by depth charges, naval mines, missiles, and torpedoes. An underwater explosion nearby a ship or submarine can be devastating to the combat readiness of the vessel. Damage may occur in the form of dished hull plating or even more serious holing of the hull. Moreover, some damage may not be obvious and can occur as a result of shock-wave loading of equipment and systems aboard the vessel. Equipment damage may incapacitate a vessel. Much research effort has been expended in the study of underwater shock, especially during the period after World War II where it became obvious that navy vessels could be disabled by a non-contact underwater explosion.[1] Thus a concerted effort was made to try and make shipboard equipment more resistant to shock. This was achieved through laboratory shock testing of equipment prior to its installation aboard vessels. With the advances in computer simulation and modeling capabilities, it is now possible to simulate a vessel's response to an underwater explosion and to identify potential problems or failures without extensive field testing. By using DDAM analytical techniques, money and time are saved.[2]

Analysis methodolgy

The DDAM simulates the interaction between the shock-loaded component and its fixed structure as the free motion of a naval vessel in water produces a higher shock spectrum than a heavy structure would when mounted to a terrestrial surface. The DDAM takes interaction into account in relation to the mass of the equipment, its mounting location, and the orientation of the equipment on the vessel.

Engineers use finite element method analysis software to verify designs using DDAM computer simulations that model the known characteristics of underwater explosion phenomena as well as the surface ship or submarine body responses to shock loading and application of a shock spectra in order to apply the appropriate shock responses at the mountings of shipboard equipment (e.g., masts, propulsion shafts, rudders, rudderstocks, bearings, exhaust uptakes and other critical structures) due to underwater explosions.[3] The analytical process is described in NAVSEA 0908-LP-000-3010, Shock Design Criteria for Surface Ships[4] which provides technical criteria for shock design calculations, and provides general background and educational material concerning application of the DDAM.

A number of commercially available computer modeling and simulation programs are available to assist in this task.[5][6] After the analyst performs a natural frequency analysis to determine the mode shapes and natural frequencies, the DDAM process then uses an input spectrum of shock design values (i.e., displacements or accelerations) based on data from a series of unclassified Naval Research Laboratory reports (primarily MR-1396, Design Values for Shock Design of Shipboard Equipment[7] and FR-6267, Background for Mechanical Shock Design of Ships[8]). Compliance standards for DDAM simulation and analysis software are maintained by the Naval Sea Systems Command (NAVSEA).

Reporting formats

The Naval Sea Systems Command (NAVSEA) established a standardized format to describe the content and formats for publishing results of the DDAM analyses and technical reports. These templates are called Data Item Descriptions (DID); once these are specified or tailored for a specific contract, they become Contract Data Requirements List items (CDRLs) that represent the deliverable items of a contract. Exactly which data items are required for delivery depends on the nature of the project. The DIDs for DDAM activities are the Analysis Report, Dynamic Shock, Mathematical Model Report, Dynamic Shock Analysis, and Dynamic Shock Analysis Extension Request.[9][10][11]

References

  1. ^ Barber, Pam; Arden, Kevin. "Dynamic Design Analysis Method (DDAM) Using MSC/NASTRAN". Newport News Shipbuilding, Newport News, VA. Retrieved June 28, 2012. 
  2. ^ "DSTO-GD-0109, The Response of Surface Ships to Underwater Explosions". Defense Science and Technology Organization - Commonwealth of Australia. September 1996. Retrieved 2012-06-26. 
  3. ^ "SUPSHIP 280-2, Guide for Mathematical Modeling and Dynamic Shock Analysis of Rudders, Rudder Stocks, and Bearings". Supervisor of Shipbuilding, U.S. Navy. December 1970. Retrieved 2012-06-26. 
  4. ^ "NAVSEA 0908-LP-000-3010 (Revision 1), Shock Design Criteria for Surface Ships". Naval Sea Systems Command. September 1995. Retrieved 2012-06-26. 
  5. ^ "Nastran Finite Element Analysis and Simulation Software". NEi Software. Retrieved 2012-06-28. 
  6. ^ "Dynamic Design Analysis Method (DDAM)". Autodesk, Inc. Retrieved 2012-06-30. 
  7. ^ "MR-1396, Design Values for Shock Design of Shipboard Equipment". Naval Research Laboratory. January 1965. Retrieved 2012-06-26. 
  8. ^ "FR-6267, Background for Mechanical Shock Design of Ship's Systems". Naval Research Laboratory. 12 March 1975. Retrieved 2012-06-26. 
  9. ^ "DI-ENVR-81030, Data Item Description: Analysis Report, Dynamic Shock". Naval Sea Systems Command. 26 Sep 1990. Retrieved 2012-06-28. 
  10. ^ "DI-ENVR-81031, Data Item Description: Mathematical Model Report, Dynamic Shock Analysis". Naval Sea Systems Command. 26 Sep 1990. Retrieved 2012-06-28. 
  11. ^ "DI-ENVR-81279, Data Item Description: Dynamic Shock Analysis Extension Request". Naval Sea Systems Command. 28 Jul 1992. Retrieved 2012-06-28. 
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 



Copyright © World Library Foundation. All rights reserved. eBooks from World Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.